Latest Products
-
WATER PUMP, ENGINE COOLING THERMAL MANAGEMENT MODULE FOR AUDI S3 8V / TT 8S / GOLF 7 GTI / GOLF 7 R / LEON 5F CUPRA 1.8/2.0 TSI EA888.3 MQB
€ 350.00 TAX included
-
TIMING CHAIN KIT FOR 2.0 TFSI EA113
€ 130.00 TAX included
-
CAM FOLLOWER FOR 2.0 TFSI EA113
€ 30.00 TAX included
-
AP SPORTFAHRWERKE COILOVER KIT
-
ST SUSPENSIONS COILOVER KIT
-
- Street Comfort
Products to improve driving and operating comfort - Street Performance
Coilovers for an individual look and to improve driving dynamics on the road - Track Performance
Clubsport & racing suspensions to achieve the fastest possible lap time
For quotation please fill the budget form on our webshop.
- Street Comfort
-
ST Coilover Kits enable you to individually adjust the ride height of your car to improve the appearance and driving behavior. Depending on your selection, ST coilover kits offer a wide range of adjustments giving you the tools needed to dial them in to your requirements.
For quotation please fill the budget form on our webshop.
-
ap coilover kits offer the possibility to adjust drivers the desired lowering accurate to a millimeter for the sporty ambitioned driver. ap offer sporty handling and ideal performance in combination with the maximium lowering.
For quotation please fill the budget form on our webshop.
-
Length: 100mm
Aplication: Radiator / Coolant / Air / Water
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
Length: 1000mm
Aplication: Vaccum Lines & Coolant Overflow
Reinforcement: None
Temperature Rated: -60ºC to +180ºC
Material: Peroxide Cured 70 Shore Silicone -
Length: 100mm
Aplication: Radiator / Coolant / Air Hose / Water
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
Length: 100mm
Aplication: Radiator / Coolant / Air Hose / Water
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
Length: 100mm
Aplication: Radiator / Coolant / Air Hose
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
Internal Diameter: 60mm
Length: 100mm
Aplication: Radiator / Coolant / Air Hose
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
– Prolonged tyre life
– Improved performance
– Increase safety
– Greater cost-effectiveness -
– Prolonged tyre life
– Improved performance
– Increase safety
– Greater cost-effectiveness -
70mm to 51mm
Length: 100mm
Aplication: Radiator / Coolant / Air Hose / Water
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
Length: 100mm
Aplication: Radiator / Coolant / Air Hose / Water
Reinforcement: Polyester
Temperature Rated: -60ºC to +180ºC -
BMC Complete Washing Kit
(Detergent + Spray)
-
– Direct bolt on
– Built in micro cat
– 100% stainless steel
– Compatible with any O2 sensors
– 90° bent structure for better access -
Sabelt seat sliding runners are made to fit Sabelt and Sparco seats directly and to allow sliding movement backwards and forwards.
-
Reduce temperatures!
- Thermal insulation of manifold/exhaust components
- Reduces engine bay temperature
- 15m x 50mm width (1.6mm thick)
- Material : titanium finish fiberglass
-
This VWR black anodized, aluminium billet washer bottle cap for the VAG Group engines (see list below) is all about detailing, representing stylish detail for your engine bay, that’s a great upgrade for the oem plastic housing.
-
Technical Information:
Length: 15m
Width: 50mm
Direct heat resistance: 1800F / 1150 degree Celsius
Intermittent heat resistance: 2500F / 1400 degree Celsius
Colour: titanium -
This Racingline billet MQB expension cap is all about detailing, representing stylish detail for your 1.4 TFSI / 2.0 TFSI / 2.5 TFSI / 3.0 TFSI / 4.0 TFSI TFSI engine bay, that’s a great upgrade for the oem plastic cap.
-Direct bolt on
-T6061 aluminium CNC
-Gloss black anodised
-Laser etched logo
-Made in UK -
This Racingline billet fuel cap is all about detailing, representing stylish detail, that’s a great replacement for the OEM plastic cap.
-Direct bolt on
-T6061 aluminium CNC
-Gloss black anodised -
The Racingline black aluminium oil filter housing is nothing more than an aesthetic detail for the 2.9 / 3.0TFSI engines of the Audi S4/S5 and RS4/RS5 B9.
Replacing the standard plastic one, this machined and anodised aluminium housing will ensure a clean and sober look to your engine while optimally protecting the filter during its entire life.
-
Monitor your 0-60mph, 60-130mph, 100-200kmh, 1/4 mile, 1/2 mile performance, and more!
-
This Racingline Performance wheel studs and nuts kit allows you to replace the factory bolts for a stud and nut system. This kit, besides having a more modern esthetic, will makes wheels swap for track or winter much easier and faster than using OEM bolts.
-
The Racingline Performance paddle shifts, available in titanium silver or black finish, are a direct replacement for your OEM RS3 8V / TTRS 8S paddles. Once the original paddle shifts removed, the Racingline ones can be installed without any modifications to enhance your interior look and efficiency.
-
The latest iteration of GFB’s feature-packed electronic boost controller now has the ability to monitor and display your engine’s air/fuel ratio in either Lambda or AFR. By connecting the analogue output of most wideband O2 controllers (i.e. Innovate LC-2, AEM UEGO etc, sold separately) to the G-Force III’s auxiliary input, you can toggle between boost pressure and air/fuel ratio display. Not only does this save you from having to install a separate AFR gauge in your car, it can also save your engine!
-
A stainless steel silencer with a built-in damper
Can height / width – 130×220 mm
Valve type – Electric Inlet -
A stainless steel silencer with a built-in damper
Can height / width – 130×220 mm
Valve type – Vacuum -
These Forge Motorsport blow off valves are a direct replacement for the OEM Audi RS4 B9 valves that integrates seamlessly with the OEM electronics and results in absolutely NO fault codes or check engine lights ! These valves will not only improve your engine performance but remedy the failure experienced with OEM valves while bringing the desirable blow off valve sound.
-
This Racingline Performance front strut tower bar is a direct bolt on upgrade to sharpen up your Audi B9 handling responses and steering feel ! Made from high quality aluminium with sophisticated liquid titanium silver finish, this bar will finish off your engine bay to the standard the B9 deserves
-
The CTS Turbo decat downpipes for Audi RS4 B9 and RS5 B9 are a direct replacement for the OEM catalysts. In addition to unleashing the power and performance of your 2.9 TFSI engine, these handmade downpipes will make your car sounds like the supercar it really should.
-
The Racingline Performance intake made from premium carbon fiber, is a direct bolt on upgrade that retains the efficient original lower box improved by the use of a carbon fiber lid and air diffuser, a high flow trifoam air filter and a large volume silicone intake hose !
Coming with all required hardware, this Racingline Performance intake will bring extra horse power and reduce turbo response.
-
– Direct bolt on
– Large volume carbon fiber airbox
– Washable and reusable air filter
– Carbon fiber intake pipe
– Glossy finish
– Aggressive sound
– Mounting kit included
– Assembly instructions included -
The 2.9 TFSI EA839 engines of the Audi RS4 / RS5 B9 are equipped with a air-water cooling system featuring radiators and intercooler. In order to provide optimal charged air temperatures on tuned engines, Wagner Tuning offers this radiator which replaces the standard one with a 55% larger volume, allowing it to withstand high powers. Coming as a direct bolt on upgrade this radiator is available with a specific installation kit to select, in order to fit with the OEM intercooler or the Wagner Tuning high performance intercooler.
– Direct bolt on
– Size : 690 mm x 490 mm x 40 mm
– 55% bigger than OEM
– High quality aluminium made
– Instructions included
– Hardware included (for OEM or Wagner Tuning intercooler) -
– Direct bolt on
– 16hp dyno proven gain
– Carbon fiber airbox featuring unic high flow venturi system
– High performance washable air filter
– Carbon air diffuser working with the OEM duct
– Fully sealed system with high glossy finish -
core dimensions stock intercooler:
220 mm x 100 mm x 85 mm
V = 1,87 Litercore dimensions WT intercooler:
222 mm x 200 mm x 120 mm
V = 5,33 Liter (+185%)